Western Branch Diesel Charleston Wv
Let's Go Brandon, Let's Go Brandon.. Yell it till their heads x-splode. I discovered this when I tossed something into the rear well that plugged up the drain. The 1" pick up will give you more than enough water for EVERYTHING going on inside in the engine compartment. So the transom mount got my attention. Skill Level: 2 of 5. It just seemed to me that it would be easy to pack mud in that setup. Inside connection is 1″ male NPT. I had raised it another 1/4" for this run and lost pressure at 78mph. Transom mount water scoop. PKUP-8018 2″ VEE SCOOP WATER PICKUP is designed specifically for stepped hulls and allows maximum water intake with minimal air notorious with aerated sterns on the stepped hull design. 08-08-2017, 02:30 PM #2Screaming And Flying!
Reference ID: c08c9ad9-be2e-11ed-a73b-77617a6d7442. I ran the 3/4 wire reinforced hose from it to the intake only to find that the fittings on the intercooler are 5/8":banghead: Now I need to call Hardin marine and get the 5/8 vice the 3/4 pressure valve to go with my inline "T". It only stick 1/2" below the hull. Zimm, the water pick up you selected i believe is a through hull fitting for flushing your engine.. look at this link, theirs a few 3/4'' fittings that go on the bottom of your you plan on using a electric water pump to circulate the water through your inner cooler? Installing a Transom-Mount Transducer on a Boat. The imco does flow a lot of water that should be fine. 24 SEB (soon to be laid up). 1 1/4″ N. Male X 1 5/8″ O. The impellor is a lot lower in the water than a transom mount would be at slow speed and not sure if it would prime itself etc.
This quality heavy duty water pickup can be used to feed water to the bait tank whilst the boat is underway. It should be as close to the centerline as possible but at least 3 inches outside the swing radius of the prop blades. Transom mounted low water pickupjojo. Took one video using a waterproof camera of the lower unit losing water pressure that came out real nice. If I remember correctly double rigged has some pretty trick water pickups on his boat maybe he will chime in. Make sure the connector plug on the cable matches the transducer port for your particular brand of fish finder. With the bracket removed, apply marine sealant such as 3M 4200 (suitable for below-the-waterline applications) to the supplied three No.
Please make sure that Javascript and cookies are enabled on your browser and that you are not blocking them from loading. Griz was right, this is the right way to do it. Which one you looking at? Tip: Drill the holes at position B on the template for hulls with reverse transom slopes of between 16 and 22 degrees. If the transducer accidentally gets latched before mounting to the transom, slots on each side of the bracket allow a screwdriver to be inserted, releasing the bracket. • Phillips screwdriver. Right now the raw water goes through the heat exchanger, p/s cooler, oil cooler, then the exhaust. External low water pickup. IMCO has a nice pickup... looks like a rams horn and fits around the drain plug in the outside of the transom... looks like all you have to do is drill a hole above the drain... gcarter. BuddyRo wrote:If you don't use them, then yes close the seacocks.
Won't do anymore of them. Sent from my iPad using Tapatalk. Key west advertises them as high speed livewell pickups, and they work 90% of the time. The most nerve racking part of this project was drilling and tapping the lower unit. Pickup mounted water tank. It's a 2015 210 bay reef. It is a 13' Biel full tunnel with a 130hp Yamaha. I built he pickup out of stainless steel and i will say i have added some material to the trailing edge of the pickup since this photo was taken so it would hang down and catch more water.. i wasn't getting the PSI i wanted with it as pictured. 13' Biel tunnel AKA "Flight Risk". It is also recommended to change lower-unit impellers and propeller nuts annually.
Any pics or suggestions on method, brands, etc is appreciated. Isn't the intercooler completely separate from the engine cooling system? Check out this new engine cooling water intake. I ordered this 3/4" one from Dana: Now the question is how to install it? While I know how to fish, it was usually on other people's boats or from the shore.
You also want to mount the water pickup as far back to the transm to the lowest point on the boat, kinda by your drain plug... i prefer the scoop style yes use 5200 but plan on never removing it tho. "A quick temper will make a fool of you soon enough. Also are nose cones the way to go, and do they realy just stick on with epoxy and stay put? • Stern Saver mounting block, to avoid drilling into the transom ($49. Bait Tank Water Pickup - Stainless. I figured if i could get my water from the top of the tunnel then i would be getting good clean water. 1″ N. Male High Speed Thru Bottom Stainless Water Pickup. I looked at every water pickup I could find on the internet. Your browser does not support cookies. Manufactured with a 45 ͦ angle toward the rear and available with flange angles to the side.
I looked all around to make sure something wasn't amiss then realized the small on off valve in the plastic fitting from the pump was open.