Western Branch Diesel Charleston Wv
Once the stock is removed, you will see two screws on the back of the receiver. First, unscrew the stock screw, then remove the stock. Caution: The Trigger housing pin is very small and has a tendency to roll. I have a 535, not 500, but the procedure is essentially the same. F. Once all shotshells have been removed, physically and visually check the magazine tube to ensure there is no ammunition left in the magazine. Using slight thumb pressure on the base of the shotshell to help it clear the elevator, pull it free from the magazine and out the loading port on the bottom of the gun. 12 Gauge Magazine Tube Dent Removal Tool. Point the muzzle downward and shake the shotgun in an up and down motion until the wooden dowel falls through the opening at the end of the magazine tube. Been using them for years and swear by them). I have done it before. Hi Gang, I am no newbie when it comes to disasembling and re-assembling my firearms but I have to admit that I am bumfuzzled by this problem: How the heck do you remove the magazine tube from a Mossberg 500? TFB FIELD STRIP: MOSSBERG 500 SHOTGUNS.
Was this article helpful? Now that you have the shotgun disassembled, you can clean it thoroughly. Dog, just take a common screwdriver and a folded rag. Assemble the gun in the reverse order of disassembly. Mossberg 500 barrel removal. This shotgun has literally been fully loaded for almost 15 years, the magazine spring is so weak it can barely push out the last 2 shells. Next, you will need to remove the trigger assembly. Remove the magazine tube cap, which is located at the end of the magazine tube, by unscrewing it counter-clockwise.
The Bolt is removed from the front of the receiver, where the barrel had been. Next, slide the forend forward until it is able to be removed. Introduction: How to Disassemble a Mossberg 500 Series Shotgun. This can cause serious malfunctions in the firearm's operation endangering the operator and those nearby. The final step is to remove the safety button by pushing it in and turning it counterclockwise. It wasn't that difficult with a little leverage! This is the only step requiring the use of a tool (punch, small screwdriver, Allen wrench, etc... ). You may have to fully or partially close the action while doing this. The Mossberg 500 is a popular pump-action shotgun used by many shooters for hunting and home defense. The first step in disassembly is to ensure your shotgun is unloaded. To Remove Magazine Plug - Mossberg 930 935 - 's Guns. Then, apply a light coat of oil to the action slide assembly. Not an easy chore and one that has the potential for damage, so unless you've got a really good reason I wouldn't do it. I didn't heat mine for fear of melting the follower but it came off eventually.
These screws hold the trigger assembly in place. From the factory, the mag tubes are attached with a large amount of loctite. I was going to change the mag tube spring, but I figured i'd give the shotgun a good cleaning and call it a day. Remove the elevator, by pinching the arms together so that their studs clear the holes in the sides of the receiver, then lifting it out.
Last edited by weevil; 07-29-2010 at 09:46 PM. The rear of the trigger guard can then be pulled downward and out of the receiver. The Follower will be loose so keep a hand close by the receiver. Continue reading here: Mossberg Models Are Designed To Fire And Gauge Shotshells Only. These screws held the stock in place. Roll the gun onto its right side, to allow this shotshell to fall out of the ejection port, into your hand. Before we get started, the four gun safety rules are listed below as a reminder. Then, clean the outside of the barrel with a damp cloth. Mossberg 500 magazine tube and barrel. Celebrating our madness for over. Now it's time to remove the barrel from the receiver. Any suggestions how I can get this thing off without causing damage? I ended up using a barrel wrench and clamping the receiver into a machine vise. REMEMBER the four rules of gun safety: - All guns are always loaded. While the shotgun is relatively easy to operate, it is important to know how to disassemble the weapon for cleaning and maintenance.
D. Physically and visually check the chamber and elevator to ensure there are no shotshells present, then move the forearm forward and close the action. Move the forearm to a middle position where the action is halfway open. How To Disassemble Mossberg 500 | Best Idea. This will keep your shotgun in top working condition, even in harsh environments. To remove the forend from the barrel, start by unscrewing the forend cap, located at the front of the barrel. The only real significance being whether your model has a captured takedown screw on the barrel assembly, or a removable cap at the end of the magazine. Caution: Do not pull the trigger when the trigger assembly is out of the shotgun because it may damage the part.
"Sacramento" Bruce Conklin. Check to make sure the barrel and mag tube are empty. Remove the forearm from the gun by pulling it forward, off the receiver. Squeeze the legs of the lifter and slide the assembly out of the bottom of the receiver.
Finally, wipe down the stock and forend assembly with a damp cloth. It fits into the hole on the right side of the receiver. Make sure the safety is on (safety button pushed reward with no red dot showing).